Display, menus and programming
5 questions
ECO Function: what is it, what is it for and how does it work?
The ECO function is an energy-saving feature available on machines with an LCD display. It is designed to reduce energy consumption when the machine remains unused for a period of time by automatically switching it to a lower-energy operating mode.
What is it for?
The ECO function prevents the machine from permanently maintaining its normal operating temperature when it is not being used. Once a configured period of inactivity has elapsed, the machine automatically enters ECO mode.
How to enable / disable the ECO function
- Switch the machine off using the main power switch.
- On keypad 1, press and hold the combination of 1 Large Coffee + Continuous + 2 Large Coffees.
- Switch the machine on using the main power switch without releasing the button combination.
- Keep the buttons pressed for a few seconds until the ECO mode option appears on the display.
- Change the status between ON and OFF using the 1 Large Coffee button, which will remain flashing while you are on this screen.
- Activation is also confirmed visually:
- if the function is set to ON, the 1 Espresso button LED remains illuminated,
- if the function is set to OFF, this LED remains off.
- Once the function is set to ON, switch the machine off using the main power switch.
How to configure the ECO function
- With the machine switched on, enter the technical menu and navigate through the menu until you reach the Heating option, ensuring that the selected value is ON/OFF.
- Press OK to enter this option and continue navigating until you reach the ECO mode inactivity time parameter.
- Adjust the desired time. The default value is 30 minutes, but it can be increased or decreased.
- Exit the technical menu by pressing the Power button.
- Leave the machine in normal operating mode. From that moment onwards, once the configured inactivity time has elapsed, the machine will automatically enter ECO mode.
What happens when ECO mode is activated?
When the configured inactivity time is reached, the machine enters ECO mode, switches off the illumination of all buttons and leaves only the 1 Espresso button of the left-hand group illuminated.
How to exit ECO mode
To exit ECO mode, simply press any button. At that moment:
- the machine exits ECO mode,
- it begins heating back up to its normal operating temperature,
- the 1 Espresso buttons on all groups remain illuminated,
- and all other buttons flash until the machine reaches the set temperature.
Once the operating temperature has been reached, all buttons illuminate normally.
The machine remains operational
The machine remains fully operational while it is recovering temperature after exiting ECO mode. The keypad illumination only indicates that the machine has not yet reached its normal operating temperature.
How to add a logo to the display
To upload or change a logo on the TFT touch display of a dual-boiler machine, enter the technical menu with the display in OFF mode, go to Display config. → Company → Select image and connect a USB drive containing the image you wish to upload. The file must be named logo.bmp, be in 24-bit BMP format, and have a maximum size of 180 × 100 pixels. The USB drive must have a capacity of 8 GB or less. If no customisation has been uploaded, the display will show the Iberital logo by default.
More information in the manual:
Is this the correct control unit?
To determine whether a control unit is the correct one, it must be verified that it corresponds exactly to the machine model and its technical configuration. It is not sufficient for the connectors to match. The machine type, the temperature control system, whether it is equipped with a display, whether it has IoT, and whether it operates with a contactor or sicurezza must all be verified. An incorrect control unit may cause the machine to power on but generate alarms, fail to heat, or exhibit unusual behaviour.
I have replaced the control unit and the machine is behaving strangely
If the machine starts behaving strangely after replacing the control unit, before assuming there is a fault, check that the control unit corresponds to the correct model, that the wiring is correct and that the temperature control configuration has been properly adjusted.
On some machines, it is also advisable to perform a reset so that the control unit can automatically detect whether the machine operates with a pressure switch or a temperature probe.
In addition, after replacing the control unit, it is usually necessary to reprogram the doses and check the display contrast setting.
If unusual behaviour still persists, the wiring, keypads, flowmeters and possible faults in the control unit itself should be checked.
Auto ON/OFF programming (only on machines with Display and/or IoT connectivity)
The Auto ON/OFF function allows the machine to be programmed to switch on and off automatically according to the day and time. This programming is managed from the display and forms part of the user menu/time settings menu.
LCD Display
To enable Auto ON/OFF, enter the user menu, adjust the time and day if necessary, access Auto ON/OFF and define the ON and OFF times for the days you wish to programme. To disable it, enter the same option and leave the ON and OFF fields as --, checking all configured days.
TFT Touch Display
To enable AUTO ON/OFF, enter the display menu, access AUTO ON/OFF and define the switch-on and switch-off time periods for each day. To disable it, enter the same option and delete or disable the saved automatic schedules.
More information in the manual: